Canadarm2
A spacecraft the weight of a loaded truck comes at you at 28,000 km/h. This arm reaches out and grabs it.
In one sentence
Canadarm2 is the International Space Station's main robotic arm, a seven-jointed, 17 m manipulator that assembled the station and now grapples visiting cargo vehicles.
The wow factor
Three things that make Canadarm2 genuinely impressive.
It can handle payloads of up to 116,000 kg, roughly the weight of eight school buses.
It has no fixed base: either end can grip the station, so it "walks" end over end across the outside like an inchworm.
Since 17 September 2009 it has performed "cosmic catches", grabbing free-flying cargo ships such as SpaceX Dragon and Japan's HTV.
How it works
A step-by-step breakdown, in plain English.
- 1Cameras on the arm and the station give astronauts inside, or controllers on the ground, views of the target.
- 2An operator flies the arm from a robotics workstation; software translates hand-controller inputs into coordinated motion of seven joints.
- 3Three shoulder joints, one elbow and three wrist joints give it the same degrees of freedom as a human arm.
- 4A Latching End Effector at each end grips a grapple fixture, powers the arm through it and locks on.
- 5To relocate, the free end grabs a new fixture, the old end lets go, and the arm steps across the station.
Where you've probably seen it
Canadarm2 appears on Canada's five-dollar banknote and in almost every photo of a Dragon or Cygnus capsule arriving at the station; its predecessor flew on the Space Shuttle.
The team behind it
Developed for the Canadian Space Agency, with Spar Aerospace as prime contractor; Spar's space division was acquired by MacDonald, Dettwiler and Associates (now MDA Space) of Brampton, Ontario in 1999. The program cost about CAD 1.4 billion.
The full story
Canadarm2 is the robotic arm of the International Space Station and Canada's best-known contribution to the program. It launched aboard Space Shuttle Endeavour on 19 April 2001 on mission STS-100 and was installed during the first Canadian spacewalk. The arm is 17 m long, has a mass of about 1,500 kg and seven degrees of freedom: three at the shoulder, one at the elbow and three at the wrist. It can move payloads of up to 116,000 kg, and because both ends can latch onto grapple fixtures, it can walk end over end around the station's exterior. Its first job was assembling the station module by module; today it relocates the Dextre robotic hand, moves spare parts, supports spacewalking astronauts and performs "cosmic catches" of unpiloted cargo ships, beginning with Japan's HTV on 17 September 2009 and including SpaceX's Dragon. Built by prime contractor Spar Aerospace, later part of MDA of Brampton, Ontario, for about CAD 1.4 billion, it was designed to be refurbished in orbit.
What do you think?
Cast your one-and-only vote. Be the first to vote.
Family tree
The predecessors and successors of Canadarm2.
- Canadarm (Shuttle)(1981)
- Canadarm2(2001)
- Dextre(2008)
Learn the science behind Canadarm2
Three Atlas entries that explain how Canadarm2 actually works.
Mind-blowing facts
The arm has no permanent base and moves around the station by grabbing one fixture after another.
It made its first capture of a visiting spacecraft on 17 September 2009.
Canadarm2 was built in Brampton, Ontario and operates about 400 km above Earth.
Plain English. Free. Unsubscribe in one click.
Sources
Every number on this page comes from one of these. If a spec is missing, no source stated it.
- Canadian Space Agency — Canadarm2 data sheetwww.asc-csa.gc.ca
- Canadian Space Agency — About Canadarm2asc-csa.gc.ca
- The Canadian Encyclopedia — Canadarm2thecanadianencyclopedia.ca
Facts checked